Blog

How to Tune A REL

High and Low Level Tuning Guide

REL products are not traditional subwoofers, but true Sub-Bass Systems. A REL is designed to augment the performance of FULL RANGE speaker systems in order to provide, in certain cases, linear response below 15Hz. A REL will take advantage of the physical room acoustics to provide deep pressurization as no traditional subwoofer can. For best results, the REL should be placed in one of the corners behind the speakers. Remember, we are dealing with True LOW bass pressurization with RELs. Low bass pressurization below 40Hz is best derived from corner placement, where the most linear and efficient low bass can be produced because the subwoofer is able to take advantage of the tangential (corner to corner) axis which is typically the longest distance in a room.

In most cases, when connecting two channel systems, you will be using the REL high level connection with the supplied cable. Please see our articles covering how to connect via High Level for details on how to connect.

To begin the set-up process, choose a piece of music that has a repetitive bass line that is very low in frequency. We suggest track 4 from the soundtrack to Sneakers (Columbia CK 53146). This has a repetitive bass drum throughout that gives you plenty of time to move the woofer around. This track is perfect for the set-up process and should be played at the highest reasonable level expected for system playback.

Working with a partner, one in the listening position and one at the REL manipulating position and controls is the most effective an efficient way to set up. If working alone, corner fine tuning and orientation can be effectively carried out from the location of the REL. Try to ignore all other music in the track, listen to the bass drum and its effect on the listening room.

The basic steps to setup are phase orientationcorner fine tuningorientation, and final settings.

Phase Orientation

With the REL in the corner the first step is to adjust for phase. Keep in mind that the right phase is whichever position (0 or 180) is the loudest for fullest. While playing music with true low bass, adjust the crossover to a point where the REL and the speaker are sure to share frequencies. This should be at 20 clicks from the minimum setting (12 o’clock) on the Crossover control. At this point turn the High/ Low Level control up so that both the REL and speaker are roughly equal in volume. This should be 15 to 18 clicks from minimum (10 to 11 o’clock) on the High/ Low Level pot. Now move the phase switch from 0 to 180 positions and listen for whichever position is loudest or fullest. That is, when the position is working in harmony with your main speakers, reinforcing bass not cancelling it. Sometimes is helps to concentrate on the leading impulse of the bass note, noticing if it is timed with the speaker. If the impulse lags the speaker’s response or if it sounds like the impulse is late, then the REL is out of phase. It will be best to determine correct phase when in the listening position, so this process will require walking back and forth to the REL if determining phase orientation alone.

 

Corner Fine Tuning

The next step is to determine precisely how far from the corner the sub should be placed to achieve the most efficient output, as well as the lowest frequency extension. With the REL fully into the corner, and pointed to the opposite corner, continuing to play the music, slowly pull the REL from the corner on the diagonal, line to opposite corner, equidistant from both side and rear wall. At a certain point (sometimes a matter of only a few inches, in rare cases a foot or more) the REL will audibly play louder, go lower in frequency extension, and truly pressurize the room as the air around the REL will seem to be energized. Stop right there! This is the correct position from the corner for the REL.

 

Orientation

Once the position from the corner has been established, the orientation of the woofer must be determined by rotating the REL from an imagined centre point at the rear of the REL. As the REL is rotated from one side to the other, listen for the greatest level of output. In effect, the REL should be left in the position where it is playing the loudest and lowest. If the REL is on carpet, at this point physically push the REL down into the carpet to lock it in place and provide the greatest coupling to the floor.

 

Final Settings

Now move both the High/Low Level control and Crossover control to 10 o’clock settings (15 clicks from minimum). In most cases this is just about where the settings will end up. The Level control should be at a setting where you can hear the REL even with the main speakers playing. This is Generally 15 clicks +/- 3 clicks. The Crossover control should be set to where the sub bass is not overpowering or sloppy. It should be in time with the impulses of the main speakers so you can hear the depth and dynamics of the low frequencies. Again, this setting is generally 15 clicks +/- 3 clicks.

 


July 23, 2015 - Posted in: How-To, Tuning Guides